Brewing Ember on the xBloom: Fan Edition
Dale's dialed-in recipe for our flavored coffees
Dale's dialed-in recipe for our flavored coffees
Dale bought a bag of our Hazelnut Cream, fell for it, and then did what perfectionists do. He wrote in asking if we had a recipe for his xBloom Studio. We didn't, so we sent him our standard pour over adapted to the machine and asked him to tell us if he found something better.
He did. A few weeks of tweaking later, he sent us the screenshots below, saved in his xBloom app under the name "Ember Flavored." It's a gentle, clean brew that keeps the hazelnut sweet instead of harsh, and it works as a starting point for every flavored coffee we roast. Thanks for sharing it, Dale.
Why flavored coffee needs a gentler brew
Flavored beans turn harsh when you push extraction hard. Hotter water and a finer grind pull more out of the coffee, and on a flavored bean that extra pull lands on the flavoring first. So this recipe runs cooler and coarser than you'd use for a single origin, and it lets the bed drain without stirring it up.
The recipe at a glance
| Setting | Dale's recipe |
|---|---|
| Dripper | Omni, grinder on |
| Dose | 18 g |
| Ratio | 1:16 (288 ml water) |
| Grind size | 80 (xBloom's French press / cold brew range) |
| Grinder speed | 120 RPM |
| Water temp | 194°F bloom, 192°F for the main pours |
| Pours | 3: 36 ml bloom, then 126 ml, then 126 ml |
| Pour pattern | Spiral, agitation off |
| Total time | 3:15 |
Step 1: Set up the coffee
Choose the Omni dripper and turn the built-in grinder on. Set the dose to 18 g and the ratio to 1:16 (more on ratios in our brewing ratio guide), which gives you 288 ml of water. Grind size goes to 80. That's coarse, in the range xBloom labels French press and cold brew. Grinder speed is 120 RPM.
Step 2: Build the three pours
The water splits into a small bloom and two equal main pours: 36 ml, 126 ml and 126 ml. That's 12%, 44% and 44% of the 288 ml.
Step 3: Bloom
The bloom is 36 ml at 194°F, poured in a spiral at 3 ml per second, then a 35 second pause. That's twice the dose in water, enough to wet all the grounds and let the gas escape before the main pours. Agitation before and after both stay off.
Step 4: The two main pours
Both main pours are 126 ml at 192°F, in a spiral at 3.5 ml per second, with agitation off. The only difference is the pause. Pour 2 rests 25 seconds before pour 3 starts. Pour 3 has no pause and drains straight through.
Step 5: Check your time
Dale's brew finishes at 3:15. If yours runs much faster, go a step finer on the grind. If it runs much slower, go a step coarser.
Dialing it in for other flavored coffees
Use Dale's recipe as written for any of our flavored coffees, then change only the water temperature, 2 degrees at a time. If the cup tastes flat and thin, go up. If it tastes harsh, come back down. Leave everything else alone so you know which change made the difference. Our guide to dialing in any coffee walks through the same idea step by step.
One thing to try
Split the last 126 ml into two pours of 63 ml with a short pause between them. It keeps the bed from flooding and can bring out a little more sweetness without adding heat. Keep everything else the same, so that split is the only thing you're tasting.
Got your own recipe?
If you've dialed in an Ember coffee on your brewer, send us the numbers at hello@embercoffee.co. Screenshots from your xBloom app are perfect. That's how Dale sent his. We'd like to see them, and the good ones might end up right here with your name on them.